Logo
Please visit our Sponsors
FAQs on Acrylic Aquarium Repair and Modifications: Scratches, Pits, Stress Fractures and Crazing 2

Related Articles: Aquarium Repair,

Related FAQs: Scratches, Pits, Stress Fractures & Crazing 1, Scratches/Crazing 3, Scratches/Crazing 4, Acrylic Repair 1, Acrylic Repair 2, & FAQs on Acrylic: Design, Leaks, Drilling/Cutting, Construction, Solvents, & Glass A quarium Repair, & DIY Gear 1, DIY Gear 2, Tanks, Stands, Covers, Custom Aquariums, Stands, Covers...,

 

Acrylic Question      8/27/14
Bob,
<.... please send all future petfish corr. to me/us at Crew@WetWebMedia.com>
I have a 125 gal acrylic aquarium that is about 8 years old. I recently emptied it out to refurbish my system and noticed some crazing along the seams (pictures below).
They do not appear to be deep, but do run along the entire seam. Is this okay, perhaps with reinforcement. Thanks.
<It is IMO/E... may not look nice, but should be structurally sound>
BTW – I love your book. I used it to start my first aquarium. My kids recently picked it up and started looking at it which led to the decision redo my system.
<Hey! Don't blame me! Cheers, Bob Fenner>
Thanks,
Alex

Used 90 gallon, too much crazing for comfort?      8/18/14
I probably visit your site daily so thanks for providing such a great source of information! On to my question which I think I know the answer to, but wanted a second opinion.
So I just bought this tank off CL which is supposedly 2 years old. The tank
holds water fine and was being used until I bought it. Here is what I noticed when I got home though (see pics).
<Oooh>
I know some crazing isn't that uncommon with acrylic tanks, but does this tank need support added or am I just being paranoid?
<I would not fill this tank w/o putting in internal corner supports. See WWM re>
Tank specifics - standard rectangle SeaClear 90 gallon (reef ready) with two openings on top (euro style?). Unfortunately the tank is 3/8 thickness, but when filled I didn't see any bowing anywhere.
The only crazing is at the bottom seams and a little on the corner. The top brace seams are fine all around. The pics included are the worst spots and they were taken with the tank dry. The seam is completely smooth on the outside and inside when I run my hand along it. So the "frosty" spots are in the seam itself.
Rest of the tank looks great, just not sure what to make of the crazing.
<Structural weakness. Bob Fenner>



 

Re: Used 90 gallon, too much crazing for comfort?      8/19/14
Ok thanks for the reply. Kind of what I thought also. This might be a silly question, but with the reinforced seams is that a very long term fix years) or a short term (a year) assuming it is done correctly? Many years (decades) of life to this system w/ the reinforcing square doweling inserted (solvented) into the corners. I would definitely be doing this job. BobF>


Surface repair of acrylic aquarium  11/21/12
Hi. I bought this 150 gallon tank and currently have it cycling. No sand or rocks in it yet (well, in the pic there is one). There is fine bubbling along the exterior surface of some of the tank. This is causing some distortion when looking from the side into the tank.
Can this be buffed out?
<Mmm, if quite shallow, yes... Think on the process here: you're grinding down the areas around... Can the tank be turned around, viewed from the less-damaged side?>
Thanks so much for any advice.
Rich
<Do see WWM re scratched acrylic tanks. Bob Fenner>

Re: Surface repair of acrylic aquarium  11/21/12
I did read thru that section.
<I see>
Is what you see in my tank called crazing?
<Mmm, looks more like some sort of external physical damage to me>
 You can definitely feel it with you hand. I'm comfortable working with sanding and polishing equipment (I've refinished
fiberglass kayaks) but don't want to start this project unless I'm certain what the defect is.
Thanks.
<As you state, could be crazing from too-thin material, perhaps a non-planar, unlevel stand... There are some good polishes about for the job. BobF>
Re: Surface repair of acrylic aquarium  11/21/12
it is also on much of the front of the tank. Almost looks like tiny bubbles in some places.
<May be imperfections in the material itself>
Sounds like what ur saying is regardless of what it is, if its only superficial it can be removed with enough TLC. Is that accurate?
<Yes, IF>
Can i send another picture?
<If you think it would help. B>
Rich
Re: Surface repair of acrylic aquarium
Another picture of the surface from a slight angle.
Rich
<... could still be the same possibilities; bad cast acrylic, crazing...
B>
Re: Surface repair of acrylic aquarium  11/21/12

Well thank u so much for your time.
Rich
<Ah, welcome!>

Re: Surface repair of acrylic aquarium     11/24/12
One last question if i can. Do u
<...>
 recommend hand only application of the sandpaper
<I don't suggest the use, ever of such on acrylic>
 or can i use a hand held vibration sander?
<Yes, but unless the scratches are huge... like a sixteenth of an inch deep or so... I wouldn't "do this" period... heat burnishing might be the route to go IF the acrylic were thick enough. Small encapsulated bubbles in the material cannot be effectively fixed>
 If not, is it fine to use an orbital sander for any of the process, specifically the polishing?
<It is not>
And i was planning on using Novus products.
Rich
<These are good products in my estimation. Bob Fenner>
Re: Surface repair of acrylic aquarium       11/29/12

Started the project. Went as low as 320 grit but those defects are still there. I did repair a section all the way out to make sure i could do it.
<Wise>
Finish after the #2 Novus was very shiny. However, i was wondering if u have used as coarse as 120?
<Dangerous... hard to remove the subsequent scratches, and may well remove too much material>
Seems like i well definitely need more than 320 to do the job. Just a bit nervous...
<Me too; having seen so many damaged, destroyed tanks... Have you tried heat burnishing just a small section? Have you contacted any of the acrylic tank re-surfacing companies? I've met Matt Conrad, owner of See Clear (SeaClear@rocketmail.com , acrylicscratchrepair.com , seemed like a nice fellow. Bob Fenner>
Re: Surface repair of acrylic aquarium       11/29/12

Started the project. Went as low as 320 grit but those defects are still there. I did repair a section all the way out to make sure i could do it.
<Wise>
Finish after the #2 Novus was very shiny. However, i was wondering if u have used as coarse as 120?
<Dangerous... hard to remove the subsequent scratches, and may well remove too much material>
Seems like i well definitely need more than 320 to do the job. Just a bit nervous...
<Me too; having seen so many damaged, destroyed tanks... Have you tried heat burnishing just a small section? Have you contacted any of the acrylic tank re-surfacing companies? I've met Matt Conrad, owner of See Clear (SeaClear@rocketmail.com , acrylicscratchrepair.com , seemed like a nice fellow. Bob Fenner>
Re: Surface repair of acrylic aquarium

Thank u. I will let u know what i find out.
Rich
<Thank you Richard. BobF>

200 Gallon Acrylic Cracks 8/25/12
Hello!
<Erik>
I was hoping you could give me advice on a few cracks I am seeing on my first all acrylic aquarium. 
<Mmm, yes... stress fractures... quite common>
The tank is 200 gallon and uses 1/2 acrylic (I am guessing this is why it is cracking).  These are the only cracks on the tank, minus some crazing and I am unsure if they are getting larger.  It doesn't seem like they could get much larger to be honest!  What will happen if the cracks get to the other perpendicular panel?
<Likely nothing>
 Is this fixable?  Is there a way to stretch the life of this tank?  Thank you for taking a look at this.  I cringe every time someone puts their hands on the tank!
Thank you again!
<I wouldn't worry. Use the search tool on WWM for the string: "Acrylic stress fractures". Bob Fenner>

Help! Acrylic Scratch Repair Nightmare (a not uncommon tale, actually) – 07/20/12
Crew,
<<Hello Dave…(wow - just had a flashback to ‘2001: A Space Odyssey’)>>
What oh what have I done...
<<Hmm…from the pic it appears you’ve been a busy boy>>
The 200G tank I acquired had heavy coralline deposits on the sides, and a fairly clear front viewing panel aside from two very prominent/large scratches that ran along the inside. I tried to follow advice given on how to use a polishing wheel and a rouge/compound to remove the scratches.
<<Mmm…>>
Somehow the tool got away from me in a split-second, and put a small but very noticeable gouge in the front display.
<<The use of power tools to remove scratches from acrylic requires some practice/experience…as you have discovered. Best for the novice to stick to manual methods of removal (elbow grease), in my opinion. Aside from the probability of causing further damage “in an instant,” the use of power tools increases the likelihood of creating a “lensing” effect in the acrylic…not that the tool is the problem, but rather going back to the technique/lack of experience of the operator. The last thing you want after removing all the scratches is to fill the tank only to find the contents look like the reflection in a fun-house mirror. You can also cause this sans power tools, but it’s likely to be to a lesser degree and more easily rectified>>
I searched WWM and spoke with several, and decided to go the sandpaper route to undo my damage and try to take out the initial blemishes (the polishing wheel didn't work as I hoped - likely my technique was poor).
<<And the polishing compound you used…more to follow on this>>
I started with a heavier sandpaper, seeing that one kit online included a 150 grit for "gouges".
<<Indeed>>
I worked my way down and back a few times. At this point, I fear that the 300 grit gouges don't seem to be coming out with the 400 sandpaper. Yikes, what have I done!
<<Fear not…this can be fixed easier than you might think>>
Can someone offer any suggestions??
<<Indeed I can…in fact several. Be sure to “wet sand” the acrylic. The use of ‘water’ helps to lubricate and cool the surface, and float-out particles. As you move up through the grits (300 to 400, etc.), do sand “perpendicular” to the scratches made with the previous grit, and until all the scratches run in the new direction. I also suggest that once you go beyond the 400-grit paper that you invest in a “quality” sandpaper. I use ‘Micro-Mesh’… It is pricey but worth it. The “grains” on the paper (actually cloth) are all equal in size which means no stray scratch marks, and a very fine finish. Micro-Mesh comes in grits from 1500 to 12000…the 1500-grit Micro-Mesh is about equivalent to 600-grit paper from the hardware or auto store. You can buy Micro-Mesh on its own (do a Net search re the name), or get it in a ‘scratch removal kit’…an advantage to the latter is it will also provide some further instruction on its use. You can also get kits that allow use with a ‘magnet cleaner’ for removing scratches/blemishes once the tank is up and running (this is handy…I know). But… Since this tank is empty I am also going to suggest you look in to the ‘NOVUS’ line of acrylic scratch removers. This is a “liquid” compound that comes in varying “grits” and works very well…either with a powered polisher…or by hand>>
This is 3/4" acrylic, so I assume I have wiggle room to get this worked out??
<<Some, yes…but don’t get excessive…remember that lensing effect I mentioned. To keep this to a minimum, you will need to increase the area polished with each successive grit. The use of a ‘wax’ pencil to mark the areas as you progress will simplify keeping up with this>>
But, I am very worried right now.
<<Can be fixed>>
I assume a power tool is required at this point.
<<Is up to you… But I would suggest this only when/if you use the NOVUS product…and then, use light pressure (e.g. – let the weight of the tool do the work), and keep the tool moving. Otherwise…”hand” removal all the way>>
Manual efforts don't seem to be working!
<<This is the best for the initial “heavy” removal…less chance of error/removing too much!>>
Please advise!
<<I have used both of these products and believe in their quality and effectiveness. With some patience and a bit of sweat, I think you will be happy with the result. Keep in mind too that although you can bring the acrylic back to “like new” with these products, very fine scratches will simply “disappear” when the tank is filled with water>>
Tank you!
Dave
<<Happy to share… Eric Russell>>

Re: Help! Acrylic Scratch Repair Nightmare (a not uncommon tale, actually) – 08/01/12
Eric, thank you!
<<Quite welcome, Dave>>
Nightmare resolved!
<<Told ya!>>
Back to a fairly clear tank.
<<Excellent>>
Thanks for the humor/levity, helped set my mind at ease...
<<Was my pleasure…>>
The labotomous fun that amateurs have working against themselves in this hobby...
<<Indeed my friend…but you are less of an amateur now, eh! Cheers… Eric Russell>>

Crazing on bottom of fish tank     7/6/12
Hello Crew,
<Michael>
I've read the entire section on "scratches, pits, and crazing" but have not seen anything related to crazing on the bottom piece of a tank.
<Mmm, happens>

 My TruVu tank is 270g (6'Wx3'D,2'T, 1/2" thick), probably about 10 years old now. There is a little crazing in the seams but nothing abnormal and it hasn't changed in the 3+ years i owned the tank. I'm more worried about the crazing going on the bottom piece. No other pieces have any crazing and there is very little bowing; really you can barley <barely> tell it bows at all. Above the stand i have a 3/4" piece of plywood (no screws or anything just laid on top), followed by 3/4" open cell foam mat; the puzzle locking kind for kids to play on.
<Good>

My tank is level from left front to right front and left rear to right rear. The left front to left back and right front to right back are both off by 1/8" equally. The bottom should be planer as well since i do not see any parts of the foam mat excessive pushed up against the bottom piece of acrylic. What makes this even more complicated, is that I do not know if the previous owner caused the crazing or if i did. I just noticed it recently when i removed the gravel.  I'd like to add some new/different gravel now but worry i won't be able to keep an eye on the crazing. This is a big risk since the tank is
sitting in my living room. Oh yeah, i also reinforced my living floor so it shouldn't be causing any twisting to the stand/tank.
Thank you for your time,
Michael
<I don't consider that there's a real problem here. Some such crazing does "happen" w/ much sheet nowayears... not a structural issue... and you have good support underneath. I wouldn't worry. Bob Fenner>

Acrylic 5 gallon tank 6/25/12
Hello:
<Hello Judy>
I got a used 5 gallon hex tank for $5 the other day. I figured I can't lose with that. The hood is great, but when I cleaned and filled up the tank, it was cloudy all over.
<Have you looked down from the top?  Is the water cloudy or is the acrylic hazed.>
 I thought it was just condensation, but it isn't. The tank may be 20 years old, I don't know, but is this what happens to acrylic tanks when they come to the end of their lives??
<May have been caused by what you cleaned it with.>
 Thank you
<You're welcome.  James (Salty Dog)>
Re Used Acrylic 5 gallon tank 6/25/12
Hello:
<Hello Judy>
It is hazed when it is filled with water. I emptied it a few hours ago and it seems to be slowly clearing from the top down. If that is hazing, what causes that?
<Ammonia based cleaning products such as Windex can cause that.>
Does that mean the tank is useless??
<No.>
The only thing I used on it was a 3000 grit sponge to clear the scratches.
<You may need to wet sand with that sponge in a circular motion.  This is called polishing is the last stage in cleaning/restoring acrylic.  You may also need to clean/polish the outside of the tank before it will appear clear.>
Thank you
<You're welcome.  James (Salty Dog)>

crack in bottom of bowfront glass tank, & crazed acrylic one      4/5/12
I've been reading your posts for a really long time but thanks to your specific answers never needed to ask anything until now. I have been reading tonight about cracks in tanks, but this tank was given to me free and it looks brand new. The people I got it from never used it and possibly the people who gave it to them might have, but again it looks new, my guess is it cracked when they tried to move it downstairs. It appears to be about 46 gallons and the crack is in about the right third front bottom piece and about 2" long starting with what appears to be a chip and then branching out thinly. I've read where you say to solvent a piece but not clear on whether to put the piece over the bottom piece or under it.
<Over>
Also, I've heard to use aquarium sealant first on the crack and then whatever you recommend to adhere the extra piece. Would you recommend just sealing it to the joints or sealing it to the actual piece all over and the joints?
<Over all is best in one go... NOT sealing the cracked area separately>
And what specifically should I use if I need to seal the crack first and then adhere the other piece.
<Glass or acrylic... aquarium-safe Silastic. Posted on WWM>
 Sorry I'm sure you've covered this somewhere but with 2 little ones at my heels I don't have days to read it all.
<Maybe get some help w/ this project>
 Thanks again!
Oh, also, I got a 55 g acrylic off craigslist of course and after filling it noticed that where it bows on the front bottom half there are lots and lots of what look like stretch marks that go in the shape of the bow like a rainbow shape,
<Crazing... see WWM re>
I had fish in it for 2 days but freaked that it would break. I attached a pic, but not sure if it's worth saving.
<Not an uncommon occurrence... w/ cheap/er acrylic, improper support... Bob Fenner>

Re Acrylic aquarium crazing? 2/13/12
James,
<David>
Thank you!
<You're welcome.>
I have discovered the tank has 1/2" acrylic, a 14" strut and 4" lip around 2 cutouts on the top. The cutouts have right angle edges, not rounds, and there is only slight whitening along the seams of the tank (front to side panels, etc).
In all, this seems a good health bill, except I'm worried about the right angle edges for the cutouts on top (versus having rounded corners).
Does any of this change your guidance?
<No. What are your concerns with the right angle cutouts?>
Again, very appreciated,
<Welcome. James (Salty Dog)>
Dave
Re Acrylic aquarium crazing? 2/13/12

I was worried based on the article about acrylic tank repair (http://www.wetwebmedia.com/acrylicaqrepair.htm) that mentions the benefit of rounded corners for the cutouts. Since it doesn't have this (i.e. it has the right angle cutouts), I wondered if I should be overly concerned.
<Since the tank has been in use and hasn't cracked yet, I wouldn't be too concerned unless these right angle cutouts were close to the two large openings. And yes, holes etc made with a hole saw or router would be better to reduce stress.
Is it possible to take a pic of the top of this tank and send to us? James (Salty Dog)>
Re: Acrylic aquarium crazing? Ammoniated cleaners?
Yep, read it myself. As you know age also will cause this depending on the type of acrylic used.
<... the citation? Not your assertion. WHERE did you read this, can anybody read this? I've been under the impression that most crazing was a sort of "stress-fracturing">
Q. Ho do you clean acrylic sheet?
A. Use a mild soap & water mixture with a gentle cleaning cloth. Do not use ammonia based cleaning solutions on the acrylic as it will eat into the sheet and cause it to craze.
The source was http://www.plaskolite.com/faq.htm
<This is their general FAQ site... Where specifically? B>
Re: Acrylic aquarium crazing?

The FAQ section here. Scroll down a bit.
http://distributionbizwiz.wordpress.com/2007/08/23/acrylic-q-a/
<Ahh, I see it now:
"Q. Ho do you clean acrylic sheet?
A. Use a mild soap & water mixture with a gentle cleaning cloth. Do not use ammonia based cleaning solutions on the acrylic as it will eat into the sheet and cause it to craze. "
<Thank you James. BobF>
You're welcome Roberto.
Re Acrylic aquarium crazing? And now leveling 2/20/12

Salty Dog (or other Crew),
<Hello Dave>
THANKS for the help here.
<You're welcome.>
I ended up buying and setting up the tank. I compared pictures of the top of the tank to pictures on your site, and can see it has slightly rounded edges on the cutouts, fortunately. I also see no signs of stress. The crazing seems to all be cosmetic, which has been confirmed by the aquarium mover (also has acrylic tank manufacturing operation here in town). As it turns out, it is only 3/8 acrylic, but as there are no signs of stress for this tank (135g, 60" x 20" deep x 24" wide), it seems I am ok.
My final concern with the setup is whether the leveling could be an issue. From front left to front right, the water line drops 1/8". From front left to back right, the water line drops 5/8" (or could be 1/2".
Seems I have an issue that must be resolved by draining the tank and shimming (sigh). The concern I have with shimming is that the acrylic stand does not have 4 legs, but a uniform base that contacts the floor at all points.
<That's not a big problem. Use full length shims under the base. If you have, or know someone with a table saw, you could rip full length shims to the thickness desired. I would not use plywood for this, especially if on a carpet. The glue could transfer to the carpet and stain permanently.>
Would you agree that this leveling is an issue, and if so - do you have any suggestions with managing it?
<My main concern would be if the tank has a slight twist in it due to not being
plumb. It's always a good idea to put 1/2" Styrofoam sheeting between the tank and the stand which
helps prevent any twisting. Another issue is that if this tank has a built in overflow and with the water level being low at the rear, your front water level may be at the top of the aquarium. If not, I'd leave it alone barring any twist in the tank. James (Salty Dog)>
Re Acrylic aquarium crazing? 2/21/12

Salty Dog: Thanks...huge help...
<You're welcome Dave.>
I did some more tank inspection and WWM research to make sure I understood tank twisting issues you had concern about.
I measured the stand, and see that it has the same exact level issues as the tank. Taking level measurements around the carpet areas surrounding the tank seem to be close to the tank/stand measures. So, seems that I have a floor (concrete slab under carpet) leveling issue. If I understand your comments, this may not be as much of a concern at these difference (i.e., biggest slope causes 1/2"-5/8" difference between back left (higher) and front right corners of tank), therefore it may be wisest at this point to just observe for signs of tank stress (such as pronounced further crazing in front right corner) but not drain/shim?
<By your comments it does not sound like there is any twisting going on here.
If the water level isn't visually objectionable, then I'd leave be.>
Also, water level does not touch the top of the front right corner of the tank. It i 1/4" below top (which I took into consideration in leveling measurements).
<Good. James (Salty Dog)>

Acrylic aquarium crazing? 2/13/12
Hello Crew,
<Hi Dave>
I have researched for enough years on your site, and finally today have placed a 50% deposit on a tank to begin my dream aquarium. Now, a few hours later, I am panicked as to whether I made a mistake.
I looked at a 130 gallon 60"l x 20"d x 24" h acrylic tank today. The current owner had it for 10 years, and acquired it from a restaurant that owned it for an unknown time period. I took pictures of the tank, and noticed what I later confirmed to be crazing throughout the front panel. Please see the attached pictures of the tank. In one picture, you can see where the flash captures the crazing - this pattern was throughout the front panel (although they seem to be minor and parallel to the floor). In another picture, you can see where the flash seems to have caught corner crazing.
Unfortunately I did now inspect the corner seams, top, or front (for bowing) closely. Do you think the visible crazing is bad enough for me to abandon my deposit?
<Crazing is generally caused by cleaning acrylic/polycarbonate with window cleaning fluids such as Windex.
<<Really James? RMF>>
As far as functionality goes, you should be fine here and the crazing will tone down once water is added. If the price is right and the crazing isn't objectionable to you, go for it. Might want to read here.
http://www.wetwebmedia.com/acraqscratch.htm>
Thanks!
<You're welcome. James (Salty Dog)>
Dave

Clarity Plus Lifetime Warranty? (and acrylic tank resurfacing/repair) -- 01/07/12
Hello,
<<Hey Garrett>>
I have recently purchased a 300 gallon acrylic aquarium from c-list for a couple bucks and thought I was getting a real deal.
<<Mmm, is often the case'¦till one sees the scratches. But even so, this can still be a 'deal' if you're willing to apply some elbow-grease. Returning the tank's clarity is not all that difficult>>
and I may have if I don't count for my labor resurfacing the tank.
<<Ah!...yes>>
My question is and it's a three part'er; how would one go about contacting the aquarium manufacturer being Clarity Plus (SeaClear, the Casco Group and so on) to attempt to cash in on said warranty?
<<If this tank has been modified or repaired (other than authorized) in any way, it's likely the warranty has been voided>>
I cannot find any contact info for them anywhere. Wondering if maybe they shut their doors?
<<Hard to say'¦their products seem to still be on offer though. You might try contacting a retailer selling their product, such as FishTanksDirect.Com>>
Second question:
Assuming I am not lucky enough to cash in on that warranty and continue doing the work myself, how clear is clear enough for acrylic?
<<'¦? You would be surprised at what 'disappears' when water is added to the tank>>>>
I have dry sanded from 120grit up to 400grit and then wet sanded from 400-4000grit and come back with polishing compound and have gotten it very clear.
<<This is likely sufficient'¦adding water will tell>>
However there still appears to be distortion from a few feet away.
<<Mmm'¦ This is from not sanding 'evenly' across the entire surface of the panel'¦or at the least 'feathering out' the perimeter of the sanded areas. Failing to do so creates what is called a 'lensing effect' and results in the distortion you are now seeing>>
I can place a book inside and still read it but can't read it looking through both panels (just a test for clarity no intentions of reading underwater).
<<Indeed'¦kind of like trying to read through two stacked glasses lenses>>
Is the distortion because I boogered-up the restoration process on the acrylic
<<A likely scenario>>
or because the tank has some age and permanent-bowing to it?
<<A less likely scenario>>
Am I worrying to much and water will fix it?
<<Possibly'¦I would test and see'¦is possible the lensing effect is not that noticeable/within acceptable viewing limits>>
(have not finished the resurface part yet to retest clarity with water, but don't want to waste my time if its going to look like poop)
Third question:
The seams of the tank in various places around the tank have turned whitish in some spots. Almost like there is frost or ice between the panels. None are very large maybe 2' at the most , but they do span the whole 1/2' of acrylic. Never owning an acrylic tank I don't know the risks involved.
<<Minimal'¦but again'¦a water test'¦>>
It would be my assumption that the chemical bond broke there just isn't leaking (have done a 2 week leak test with litmus paper on the seams to verify leaks).
<<Then you likely don't have a worry re'¦but while the tank is empty and dry you can easily beef-up these inside corners with triangular acrylic doweling>>
Do these need to be shored up with the square braces as suggested in other posts or can I take a needle with solvent and forces it in the joint? Or something along those line?
<<My choice would be the acrylic doweling'¦applied very carefully; to avoid any further marring of the viewing surfaces, with a 'thickened' acrylic solvent like Weld-On #16 or Craftics #33>>
Any and all answers and suggestion will be greatly appreciated.
<<I hope I have served>>
Thanks,
Garrett Crance
<<Happy to share'¦ Eric Russell>>

Become a Sponsor Features:
Daily FAQs FW Daily FAQs SW Pix of the Day FW Pix of the Day New On WWM
Helpful Links Hobbyist Forum Calendars Admin Index Cover Images
Featured Sponsors: